When a stainless pipe is larger than a tube mill can draw, it is made from plate. Two names get used for that work — JCOE and LSAW — and they are constantly treated as competing methods. They are not. JCOE is a forming sequence; LSAW is a welding process. A large-diameter pipe is normally both: formed by JCOE and welded by LSAW. Understanding which is which explains why a 3 m section exists at all, and why a 12 m pipe has welds in it that a seamless pipe does not.
What the four letters mean
JCOE is an acronym for the four steps of forming: J for the crimping that bends the two plate edges into a J profile, C for the progressive pressing that turns the plate into a C, O for the closing that brings the edges together into a circle, and E for the mechanical expansion that finishes the diameter. The plate enters flat and leaves as a round section with the two long edges facing each other, ready to weld.
LSAW stands for Longitudinal Submerged Arc Welding: a submerged-arc weld running along the length of the section, as opposed to a spiral weld (HSAW) or a circumferential weld. The “longitudinal” is the important word. It describes the seam that runs the length of each section, not the seams that join sections together.
The forming sequence, step by step
1. Edge milling. Both long edges are milled square and to a specified width. This is where the weld preparation begins — a milled edge gives a consistent root gap, and a consistent root gap is what makes a repeatable weld on a 1219 mm or 1524 mm diameter.
2. Beveling. The edges are cut to the weld profile: a V or a compound bevel depending on wall thickness and whether the root will be welded from inside, outside, or both.
3. J-crimping. The two edges are pre-bent over a short length. This is the step that gives the process its first letter and its main advantage: without it, the final closure produces a flat spot near the seam, and a flat spot on a large pipe is a roundness defect that no expansion can fully remove.
4. C-pressing. The plate is pressed in successive strokes into a C, working from the crimped edges toward the centre. The number of strokes is set by the diameter and the wall — a thicker wall needs more, smaller increments.
5. O-closing. The final stroke closes the C into an O, bringing the two milled edges together with the root gap set at the start.
6. Welding. The longitudinal seam is welded. The root is laid down first — gas tungsten arc for the root pass on stainless, because it gives a clean, oxide-free root without the flux that submerged arc requires — and the fill and cap passes follow with submerged arc welding, inside and outside. This is the LSAW part of the name.
7. Expansion. The section is mechanically expanded to the final outside diameter. Expansion does two jobs: it sizes the pipe to a tolerance tighter than forming alone can hold, and it stress-relieves the formed section by taking it slightly past yield in the hoop direction.
8. Cutting and end preparation. The section is cut to length and the ends are beveled for the circumferential weld that will join it to the next section.
Why one section is about 3 m
A formed section cannot be longer than the plate it came from. Plate for stainless pressure and structural work arrives at widths around 3 m, so a section measures roughly 3 m along the axis. The circumference is a separate number: at 1219.2 mm outside diameter the plate has to be about 3.83 m wide before welding, which is why the widest plate is bought and why a 48 inch pipe is close to the practical upper bound of a single-seam JCOE section.
Anything longer than 3 m, or wider than one plate, is built by joining. A 12 m pipe is four 3 m sections with three circumferential seams. That is normal construction, not a shortcut, and the seams are qualified and inspected to the same standard as the longitudinal seam.
Where LSAW stops and multi-seam construction starts
Single-seam forming runs out when the circumference exceeds the available plate width. Above that the pipe is built from two or more pressed segments — each segment formed and welded, then the segments joined with longitudinal seams, and the resulting cans joined with circumferential seams. This is how the very large sizes are produced, and it is why a 5000 mm outside diameter pipe is described by its seam map rather than by a single weld. The extra-large diameter range is built this way.
Welding procedure and qualification
Every seam is welded to a procedure qualified under ASME IX. The procedure qualification record fixes the essential variables — process, filler classification, thickness range, diameter range, position, preheat and interpass — and the welders are qualified to the same section of the code. For austenitic stainless the practical points are: no preheat, controlled interpass temperature, and a shielding gas that keeps the root from oxidizing. For duplex grades the heat input range is narrower and the procedure is written around it.
Filler selection follows the grade: 308L for 304/L, 316L for 316/L, 347 for 321 and 347H when stabilization is specified, and matching duplex consumables for 2205 and 2507. Where the pipe is ordered to ASTM A358, the class sets whether filler is required in every pass and whether the seam is fully radiographed.
Inspection on a formed and welded section
The inspection plan for a large section typically covers: dimensional check (outside diameter, out-of-roundness, wall at the seam and away from it, squareness of the ends), visual and penetrant inspection of both weld faces, radiographic examination of the longitudinal seam — 100% or sampled according to the ordered class — hydrostatic test at the specified pressure, and product analysis or PMI to confirm the grade. Material certificates are issued to EN 10204 3.1 with heat numbers traceable to the plate.
Radiography is where formed pipe differs most from seamless: the longitudinal seam is examined along its full length, and on a 12 m assembly the three circumferential seams are examined as well. The size table for NPS 8 to NPS 200 shows which diameters fall in single-seam territory and which need multi-seam construction.
Heat treatment after welding
Austenitic stainless welded sections are solution annealed at 1900 °F [1040 °C] and water quenched unless the order says otherwise. This restores corrosion resistance in the weld and heat-affected zone by dissolving the chromium carbides that form during welding. Where the grade is stabilized — 321, 321H, 347, 347H, 348 — the alternative is the stabilization treatment under A358 supplementary requirement S5, which holds the metal at a lower temperature to precipitate carbides without full annealing. Below the specified annealing temperature the pipe is stamped “HT” and the actual temperature recorded.
The short version
JCOE is how the plate becomes a round section; LSAW is how the seam along that section is welded. A 3 m section is a plate-width limit, not a design choice, and a 12 m pipe is four sections joined with qualified circumferential seams. When a size needs more than one plate width, the pipe becomes a multi-seam assembly — still the same processes, applied more than once.
If you are specifying a large-diameter stainless pipe and want the forming and welding route confirmed for your size, send the five figures — diameter, wall, grade, length, quantity — or message WhatsApp on +86 187 0667 3812.
Questions we get on JCOE and LSAW
Is JCOE better than rolled pipe? It holds a tighter roundness and diameter tolerance because of the crimping step and the expansion, which matters for pipe that has to be joined on site. Rolled pipe handles thicker walls and larger diameters more easily. Which is right depends on the tolerance and the size, not on preference.
Is LSAW the same as EFW? EFW means electric-fusion-welded and covers a family of arc-welded pipe, of which LSAW is one variant. A358 pipe is EFW; whether it is LSAW depends on the seam orientation.
Why not make a 12 m section in one piece? Because the plate is not 12 m long and the forming press works from a flat plate. Joining is the only route, and the resulting circumferential seam is inspected like any other weld.
Need a quote on a specific size?
Send the five parameters that drive the price: outside diameter, wall thickness, grade, length per section, and total quantity. We reply within one working day with a technical-commercial offer, including the proposed welding sequence and inspection plan.
