48 Inch Stainless Steel Pipe (1219.2 mm OD)

NPS 48 stainless steel pipe measures 1219.2 mm (48 in) on the outside diameter. At this size the nominal number and the real dimension finally agree: 48 × 25.4 = 1219.2 exactly. That is not true lower down the scale — NPS 8 is 219.1 mm, not 203.2, and NPS 12 is 323.9 mm, not 304.8 — so a 48 inch pipe is the first size where you can trust the arithmetic. What you cannot trust at this size is the word “Schedule”.

Why there is no Schedule 40S for a 48 inch pipe

ASME B36.19M, the stainless steel pipe schedule, stops at NPS 24. Above that the standard does not define wall thickness series at all, which is why every catalogue that lists “48 inch Sch 40S” is quoting something that has no standard behind it. Some suppliers take the carbon steel table (B36.10M) and borrow its numbers; others simply post the wall their mill happens to roll. Either way, the wall you receive is defined by the purchase order, not by a schedule designation.

In practice a 48 inch stainless order is written one of three ways: a stated wall in millimetres, a minimum wall with a tolerance class, or “per drawing” when the pipe has to match an existing spool. We quote all three. If a customer sends only “NPS 48, Schedule 40S”, we come back and ask which wall they actually mean, because the answer changes the weight, the price and the weld procedure.

Wall thickness we run at 1219.2 mm outside diameter

The table below is the working range for single-seam welded 48 inch pipe, not a catalogue of stock sizes. Anything in between is rolled to order.

Wall (mm) Inside diameter (mm) Weight (kg/m) Typical use
6 1207.2 181.3 ventilation, low-pressure air
8 1203.2 241.3 ducting, drainage
10 1199.2 301.2 water mains, outfalls
12 1195.2 360.9 process water, slurry
16 1187.2 479.4 structural casing, piles
20 1179.2 597.5 high-load structural
25 1169.2 743.7 stack liners, heavy supports
30 1159.2 888.6 pressure service, thick-wall

All weights are theoretical, calculated from the nominal wall with a density of 7.93 g/cm³ for austenitic stainless. Mill tolerance on wall moves the real weight by a few percent; we state the calculated figure so that freight and lifting plans have a defensible number. Above 30 mm the wall is possible but the section becomes a forging problem rather than a rolling problem, and lead time lengthens accordingly — the same route that takes a 5000 mm diameter pipe into thick-wall territory applies here.

One 3 m section becomes a 12 m pipe

A 48 inch pipe is not drawn as a single 12 m length. The plate is formed and welded into a 3 m section — the JCOE route, where the plate is crimped into a J, closed into an O, welded inside and outside, then expanded — and the finished sections are joined with circumferential seams. That is the same construction used for all sizes above NPS 24, and the reason a 12 m 48 inch pipe carries two welds rather than none.

The circumferential seam is the part that decides whether the pipe passes inspection. Each seam is 100% radiographed on the classes that demand it, the mismatch between the two sections is controlled, and the weld is qualified under ASME IX with a procedure that names the process, the filler and the range of diameters it covers. If the pipe is ordered to ASTM A358 Class 1 to Class 5, the class fixes whether the seam is fully radiographed or sampled every 50 ft.

Grades and the documents that come with them

The common grades at this diameter are 304/L, 316/L, 321, 347H and the duplex grades 2205 and 2507 when the service is chloride-heavy. Plate for a 1219.2 mm pipe starts at 3 m × 1.2 m or wider, so the grade has to be available in wide plate, not just in coil. That is a supply question as much as a metallurgical one, and it is the first thing we check when a 48 inch enquiry arrives.

Standard delivery includes EN 10204 3.1 material certificates with heat numbers traceable to the plate, dimensional records, and radiography films or digital files for the seams. Third-party inspection is welcome and can be arranged at the works.

Where a 48 inch pipe is actually used

At 1219.2 mm the pipe is large enough to be a structure rather than a conduit. The recurring applications are outfalls and intake lines where flow is high and head loss matters, stack and duct liners in flue gas service, pile casing and structural columns where the pipe carries load, and slurry or tailings lines where abrasion resistance favors a thick wall over a coating. Each of those pulls a different wall, which is why the wall is quoted per project rather than stocked.

What we need to quote a 48 inch pipe

Five figures settle most enquiries: outside diameter (1219.2 mm if you mean NPS 48), wall thickness in millimetres, grade, length per section, and total quantity. Add the applicable standard and any inspection requirement and the offer comes back with a welding sequence and an inspection plan attached, usually within one working day.

Request a quotation or send the five figures on WhatsApp at +86 187 0667 3812.

Questions we get on 48 inch pipe

Is NPS 48 the same as 48 inch? Yes, for outside diameter: 1219.2 mm. Nominal bore language (“48 inch bore”) is different and refers to the inside, which shifts with wall.

Can you supply Schedule 80 at this size? Not as a standard designation, because B36.19M ends at NPS 24. We can supply the wall that Schedule 80 would imply at smaller sizes, stated in millimetres on the certificate.

How long can a single 48 inch pipe be? Sections run 3 m from the forming line; assembled lengths go to 12 m and beyond with circumferential seams, subject to transport limits.

Need a quote on a specific size?

Send the five parameters that drive the price: outside diameter, wall thickness, grade, length per section, and total quantity. We reply within one working day with a technical-commercial offer, including the proposed welding sequence and inspection plan.