Large-diameter stainless steel pipe is specified by two numbers that look similar and mean completely different things: NPS (nominal pipe size) and outside diameter. Get them confused on a purchase order and the mill will confirm one thing while your fabricator cuts for another. This page gives the full mapping from NPS 8 through NPS 120, states where the schedule system stops applying, and shows which specification governs at which size band.
NPS is a label, OD is a dimension
NPS is a dimensionless designator — “NPS 12” is a name, not a size in inches. The actual outside diameter for NPS 12 is 323.9 mm (12.750 in.), because the original sizing was based on the inside diameter of a heavy wall pipe that no longer exists as a standard product. From NPS 14 upward the convention switches: the number then equals the outside diameter in inches, so NPS 14 is 355.6 mm and NPS 48 is 1219.2 mm exactly. The awkward band is NPS 8 to NPS 12, where the designation is smaller than the actual diameter.
Two rules follow from this, and they cause most of the dimensional disputes on large-diameter orders:
- Always order by outside diameter and wall thickness, with NPS quoted alongside as a convenience label. A drawing that says “NPS 36” and a purchase order that says “914.4 mm OD” agree, but only because someone checked.
- Inside diameter is derived, never specified. ID = OD − 2t. Change the wall and the ID moves, even though the NPS label does not.
Size table: NPS 8 to NPS 120
Outside diameters follow ASME B36.10M / B36.19M. Schedule 10S and 40S wall values are quoted from ASME B36.19M, which covers stainless steel pipe and stops at NPS 24.
| NPS | OD (mm) | OD (in.) | Sch 10S (mm) | Sch 40S (mm) | Governing spec at this size |
|---|---|---|---|---|---|
| 8 | 219.1 | 8.625 | 2.77 | 3.76 | A312 / A778 / A358 |
| 10 | 273.0 | 10.750 | 3.05 | 4.19 | A312 / A778 / A358 |
| 12 | 323.9 | 12.750 | 3.36 | 4.57 | A312 / A358 |
| 14 | 355.6 | 14.000 | 3.68 | 6.35 | A358 / A778 |
| 16 | 406.4 | 16.000 | 4.19 | 7.14 | A358 / A778 |
| 18 | 457.2 | 18.000 | 4.19 | 7.92 | A358 / A778 |
| 20 | 508.0 | 20.000 | 4.78 | 9.53 | A358 / A778 |
| 24 | 610.0 | 24.000 | 5.56 | 12.70 | A358 / A778 |
| 26 | 660.4 | 26.000 | — | — | A358 / A778 — wall per order |
| 28 | 711.2 | 28.000 | — | — | A358 / A778 — wall per order |
| 30 | 762.0 | 30.000 | — | — | A358 / A778 — wall per order |
| 32 | 812.8 | 32.000 | — | — | A358 / A778 — wall per order |
| 34 | 863.6 | 34.000 | — | — | A358 / A778 — wall per order |
| 36 | 914.4 | 36.000 | — | — | A358 / A778 — wall per order |
| 38 | 965.2 | 38.000 | — | — | A358 / A778 — wall per order |
| 40 | 1016.0 | 40.000 | — | — | A358 / A778 — wall per order |
| 42 | 1066.8 | 42.000 | — | — | A358 — wall per order |
| 44 | 1117.6 | 44.000 | — | — | A358 — wall per order |
| 46 | 1168.4 | 46.000 | — | — | A358 — wall per order |
| 48 | 1219.2 | 48.000 | — | — | A358 — wall per order |
| 52 | 1320.8 | 52.000 | — | — | A358 — wall per order |
| 56 | 1422.4 | 56.000 | — | — | A358 — wall per order |
| 60 | 1524.0 | 60.000 | — | — | A358 — wall per order |
| 64 | 1625.6 | 64.000 | — | — | A358 — wall per order |
| 68 | 1727.2 | 68.000 | — | — | A358 — wall per order |
| 72 | 1828.8 | 72.000 | — | — | A358 — wall per order |
| 76 | 1930.4 | 76.000 | — | — | A358 — wall per order |
| 80 | 2032.0 | 80.000 | — | — | A358 — wall per order |
| 84 | 2133.6 | 84.000 | — | — | A358 — wall per order |
| 88 | 2235.2 | 88.000 | — | — | A358 — wall per order |
| 92 | 2336.8 | 92.000 | — | — | A358 — wall per order |
| 96 | 2438.4 | 96.000 | — | — | A358 — wall per order |
| 100 | 2540.0 | 100.000 | — | — | A358 — wall per order |
| 104 | 2641.6 | 104.000 | — | — | A358 — wall per order |
| 108 | 2743.2 | 108.000 | — | — | A358 — wall per order |
| 112 | 2844.8 | 112.000 | — | — | A358 — wall per order |
| 116 | 2946.4 | 116.000 | — | — | A358 — wall per order |
| 120 | 3048.0 | 120.000 | — | — | A358 — wall per order |
| 138 | 3500 | 137.8 | — | — | A358 — per drawing |
| 157 | 4000 | 157.5 | — | — | A358 — per drawing |
| 197 | 5000 | 196.9 | — | — | A358 — per drawing |
Above NPS 120 the NPS value becomes a working label rather than a standardised designation; the last three rows are shown because they are real project sizes for circumferential-welded shells, not because ASME publishes a schedule for them.
Above NPS 24 the schedule system stops applying
ASME B36.19M covers stainless steel pipe from NPS 1/8 through NPS 24. That is the entire range of Schedule 5S, 10S, 40S, and 80S. Beyond NPS 24 there is no schedule wall thickness in the stainless system — not at 40S, not at 80S, not at any schedule.
This is the single most common error in large-diameter enquiries. A specification that says “NPS 48, Schedule 40S” is asking for something that does not exist. What the project actually needs is one of these:
- A stated wall thickness in millimetres or inches — for example “OD 1219.2 mm, WT 12.7 mm”.
- A wall thickness per ASTM A358 or A778, where the wall is a project decision rather than a schedule lookup.
- “Per drawing”, when the design thickness comes from the pressure calculation and the pipe is built to that calculation.
Wall thickness still has to satisfy the pressure requirement, and that calculation is a code matter, not a dimensional one. The dimension table above locates the diameter; the pressure calculation sets the wall.
Worked example: weight per metre
Theoretical weight for austenitic stainless steel follows the standard line-pipe formula, using a density of 7.93 g/cm³:
W (kg/m) = (OD − t) × t × 0.02491
Two worked cases, both with the wall stated explicitly because that is how the order should read:
| Size | OD (mm) | WT (mm) | Theoretical weight |
|---|---|---|---|
| NPS 48, 12 mm wall | 1219.2 | 12.0 | 360.9 kg/m |
| NPS 120, 20 mm wall | 3048.0 | 20.0 | 1508.5 kg/m |
Weights are theoretical and assume nominal wall. Mill tolerance moves the actual figure, and for large-diameter heavy-wall pipe that movement is not trivial — a 5 percent wall variation on a 20 mm wall changes the weight by roughly 75 kg/m at NPS 120. Quote against the theoretical figure, invoice against the weighed figure, and state which one the contract uses.
Which specification applies at which size
| Size band | Typical route | Why |
|---|---|---|
| NPS 8 – 24 | A312 (seamless or welded), A358, A778 | Schedules still apply; both mill-rolled and plate-formed product are available |
| NPS 26 – 48 | A358, A778 | Plate forming takes over from mill rolling; schedules no longer define the wall |
| NPS 52 – 120 | A358 primarily, A778 for light wall | Longitudinal JCOE sections; RT class becomes the quality statement |
| Above NPS 120 | A358 with circumferential welding | Single-section capability is exceeded; shells are joined and the joint is inspected like the longitudinal seam |
What Shiwang supplies
Shandong Shiwang Stainless Steel Pipe covers the full band above NPS 8, with diameters to 5000 mm:
- Thick wall line: OD 323.9 mm to 5000 mm, wall 6 mm to 80 mm, JCOE longitudinal sections with circumferential completion above 3000 mm.
- Thin wall line: OD approximately 219 mm to 5000 mm, for ducting, ventilation, drainage and large-flow low-pressure service.
- Grades: 304/304L, 316/316L, 321, 310S and 2205 duplex as standard; 904L, Hastelloy, Inconel and titanium on request.
- Standards: ASTM A358/A778/A928, ASTM A312, EN 10217-7, GB/T 12771 and JIS G3468.
Product pages: extra-large diameter stainless steel welded pipe · large-diameter thick-wall welded pipe · large-diameter thin-wall welded pipe · ASTM A358 class 1 to class 5 explained
FAQ
Is NPS the same as inches?
No. NPS is a label. NPS 12 has an outside diameter of 12.750 in. (323.9 mm), not 12 in. Below NPS 12 the number roughly tracks the inside diameter of an old heavy-wall pipe; above NPS 12 it tracks nothing in particular and must be looked up.
Why is NPS 12 not 12 inches?
Because the older naming convention still applies below NPS 14. The number used to track the inside diameter of a heavy-wall pipe, so the outside diameter had to be larger: NPS 12 is 323.9 mm (12.750 in.). From NPS 14 upward that stops being true, so NPS 14 is 355.6 mm (14.000 in.) and NPS 48 is 1219.2 mm (48.000 in.) exactly.
Can I order Schedule 40S above NPS 24?
No. ASME B36.19M stops at NPS 24. Above that, specify the wall thickness directly, or specify it per ASTM A358 / A778, or write “per drawing”. A supplier who accepts “NPS 48 Sch 40S” without comment is likely to substitute a wall without telling you.
What is the largest diameter you produce?
5000 mm outside diameter, reached by circumferential welding of longitudinal JCOE sections for the sizes beyond single-section capability. Wall thickness up to 80 mm on the thick-wall line.
How do I convert NPS to millimetres?
Look it up in the table above. From NPS 14 upward, multiplying by 25.4 does give the outside diameter — NPS 48 times 25.4 is 1219.2 mm. Below NPS 14 it does not: NPS 8 times 25.4 is 203.2 mm while the real outside diameter is 219.1 mm, a 15.9 mm gap that will wreck a purchase order if you trust the arithmetic.
Send us the outside diameter and wall thickness you need — we will confirm availability, theoretical weight per metre, and the applicable weld class before quoting.
Need a quote on a specific size?
Send the five parameters that drive the price: outside diameter, wall thickness, grade, length per section, and total quantity. We reply within one working day with a technical-commercial offer, including the proposed welding sequence and inspection plan.
